Ayon Audio Eris

Klicka för en större bild

Det är med stor glädje vi introducerar ett Single Ended Triod försteg med stor flexibilitet och egenskaper. Eris erbjuder måttstocken av förstegs kvalitet. Ljudbilden är expansiv; allting är korrekt proportionerat, fokuserat, och fritt från grynighet. Instrument-fokus, renhet i ljudbilden och basdefinition; allt är livligt presenterat. Det finns alltid en naturlig och uttrycksfull dynamik, närhet och snabbhet som kopplar lyssnaren till musiken.


Eris erbjuder en ny dimension i återgivningen som ligger långt förbi dess prisklass.


Arbetssätt: Ren Klass A, SE-Triode

Rörbestyckning Line:  6H30

Maximal utnivå (vid1 kHz ): ~ 20V rms

S/N förhållande:> 98 dB

Ingångsimpedans: 10kOhm

Utgångsimpedans: ~ 900 Ohm

Frequensgång Line: 5Hz - 100kHz

Harmonisk Distorsion (vid 1V ) Line: < 0.01%

Ingångar: 5 x Line- RCA

Utgångar: 2x RCA, 1x XLR , 1x Tape out

Dimensioner (W x D x H): 48 x 41 x 11 cm

Vikt: 17 kg

Features & Design


Full-featured class A single-ended & triode vacuum tube stereo preamplifier
Pure vacuum tube-circuit design with single gain stage and incorporates only one coupling capacitor at its output stage


Vacuum Tubes
The choice of signal and power tubes have a significant influence on the sound and hence on the inspiration and joy of listening. This is not only the decision between good and bad tubes but finally the interaction of the different types of tubes and their combination that are used in the various Ayon amplifiers.


Signal Path
We believe that the simplest circuits work best together with the shortest signal path. The shorter the signal path is, the less possibility of sonic degradation from various sources, including the wire itself. Even on the circuit boards, the copper traces are kept to a very minimum length. The completely redesigned circuit board provides a more straightforward and direct approach to the signal paths.

  • Vacuum tube current source loading for signal gain stage
  • Very short signal path
  • Simplest direct circuit path for purest musical sound and high reliability
  • Very low output impedance to drive any tube or solid state power amp
  • No solid state devices in the signal path
  • High current and low impedance design that operates tubes in the best areas their curves
  • Minimal discrete wiring for optimum signal propagation
  • No followers or buffers in the signal path
  • High quality parts throughout
  • 0dB negative feedback (of any kind )
  • Selector switch engages relays located near RCA jacks to switch all inputs


Tube - Power Supply

The power supplies have been further refined with new components and enhanced AC line noise filtration. Low power transformer, chokes and filters provide total isolation between the input and output stages which makes this a pure power source. We also use electrolytic capacitors with much larger storage capacity to make up for the loss in filtering when using resistors in lieu of inductors.

  • Tube rectified power supply
  • Superior noise reduction
  • Low noise –insulated power transformers
  • Power transformers are encased, excellent damped and RFI/EMI ultra-shielded
  • Innovative power supply provides a high speed energy delivery on transients
  • Dual choke filtered power supply for 6H30 tubes
  • Separate and isolated power supplies over each stage of amplification
  • Regulated DC filament supplies with soft-start power up for extended tube life
  • AC power line filter to avoid noise and hash from entering into the unit.
  • High capacitance energy storage.
  • Polarity meter (0° or 180°)


Dual Grounding System
The modification of the grounding topology leads to increased rejection of noise from the power supply and other areas. The dual grounding topology used in all of our amplifiers is quite unique to the whole hi-end tube amplification industry. Such extensive topology provides for quieter backdrop for which the music can unfold in its entirety. It further establishes the quick and controlled bass response and the full bodied expression of the high frequency. The ground leg of the signal has not been neglected and given meticulous attention in its implementation. The importance of proper grounding cannot be over emphasized.

  • Ground switch
  • Central one-point star earth grounding
  • Dual grounding system (switchable)


The type of parts used therefore must have a synergistic relationship to the circuit they are placed in. It is this relationship of which type of part to use where, that ranks our products apart from the mass.

  • High selected, best quality passive components used in all applications
  • High speed & high quality audiophile grade coupling capacitors
  • Special tube sockets with beryllium- copper spring pins, custom made by Ayon
  • High quality – RCA input jack
  • Neutrik/Swiss - XLR chassis connectors
  • Special isolated - internal wiring
  • Gold-plated industrial grade PCB
  • High quality - Input selector switches
  • TKD – Volume potentiometer - 2 channel version


Mechanical Construction
The high grade aluminum chassis impart a richer, more lustrous tonality with a cleaner background and less hash and grain. All brushed anodized anti-vibration-resonance and non-magnetic chassis's are fully hand assembled to insure the highest level of craftsmanship.

  • 4 chrome knobs, custom-made by Ayon
  • The aluminium feet are resonance absorbing types
  • All front & rear panel descriptions are engraved
  • Ground switch
  • AC phase polarity control indicator
  • Volume & Mute function - RC
  • Metal remote commander
  • Chassis finish: black